Solitary reduction worm gearing offers high ratio reduction with couple of shifting parts in a close-coupled small drive. The right angle set up of driving-to-driven machine takes a minimum of space. Input and output shafts can be prolonged in either or both directions in horizontal or vertical plans adaptable to any installation requirement. Efficient electric motor speeds are decreased to gradual speed requirements of many industrial machines in a single reduction.
Product Features
Ratios 5:1 to 70:1
Hollow & Solid Output Shafts
Vertical & Horizontal Mounting
Fan Cooled (Standard)
Motor Mounts (C-Encounter Adapters or Scoops)
Cast Iron or Steel Housings
Products
The exclusive utilization of the involute Helicoid Thread form (with departing side contact) on the worm and gear provides for high efficiencies, and long service lifestyle. The hardened ground and polished alloy metal worm develops a clean, work hardened surface area on the bronze equipment. Because of this worm gears put on in and improve with extented service while various other gears are deteriorating. Ever-Power offers a wide collection of model configurations, sizes, ratios, and accessories from our standard product line.
Fabricated Designs
If your application involves severe shock loads or feasible housing damage from external sources (as in steel mills or mobile devices applications) Ever-Power can provide fabricated steel housings with up to a 48″ center distances. Fabricated housings provide maximum rigidity and strength that allows the tranny of higher horsepower levels than are worm gear speed reducer possible with regular cast iron units. Extra heavy part plates connect the worm and equipment shaft bearing supports, assuring proper meshing of the apparatus under all load circumstances. In smaller sized sizes, fabricated steel reducers are interchangeable with Ever-Power regular cast iron reducers.
Custom Designs
Ever-Power can offer custom swiftness and reversed engineered reducers for your application, be it a fresh project or a primary drop-in alternative to a competitor’s quickness reducer. Fabricated metal reducers enable Ever-Power to match a competitor’s footprint, centerline, and shaft elevation allowing a direct drop-in replacement saving the customer time and money.
Long – Quiet Life
All worm gears in Ever-Power reducers are produced from phosphorous bronze. Our design also incorporates a hardened, surface and polished alloy steel worm. This combination develops a smooth, work-hardened mating surface area of the bronze equipment which enhances with prolonged service.
Worm gearing is a class of gear reducers that utilizes correct angle, nonintersecting shafts. This form of reducer provides soft and quiet procedure and permits the likelihood of large velocity reductions. These gears are available from share in a wide selection of ratios, from as low as 4:1 to as much as 3600:1. The small design and structure allows worm gear reducers to be positioned in a comparatively small space. Thus, high reductions in a restricted package size can be achieved with this configuration. Our worm gear features the constant sliding tooth actions between worm and one’s teeth. This escalates the tolerance for weighty loads and shock loads. Worm gear drives provide users high reducing capacity for relatively low cost when compared to various other types of gearing.
The usage of worm gearing extends across many industries including food, beverage and grain and has many applications. Some applications that use worm gearing are: conveyors, mixers and bucket elevators.
Ever-Power worm gear reducer gearbox series base on years of experiences uses designed teeth surface with unsurpassed torque transfer overall performance with great performance, efficency and price.Worm gear system transmits power through sliding get in touch with, leading to extremely low vibration , sound, little backlash and self-locking property
-Housing:One time we casting creats great rigidity for severe impacts. Outer cooling fins and internal lubrication essential oil diversion channel style to improve heat dissipation.
-Worm Shaft: Manufactured with Carbon alloyed Steel S45C or SCM415, precison machined and carburized to HRC45 or HRC60, then for precision tooth grinding to ensure maximum contacting.
-Worm Wheel: Manufactured with Carbon alloy ALBC2, teeth are machined by precision CNC hobbing machine to sustain high impact.
A worm equipment reducer is one type of reduction gear box which includes a worm pinion insight, an output worm gear, and features a right angle output orientation. This kind of reduction gear box is normally used to have a rated motor velocity and create a low speed output with higher torque worth based on the reduction ratio. They often times can solve space-saving problems because the worm gear reducer is among the sleekest reduction gearboxes available because of the small diameter of its result gear.
worm gear reducerWorm equipment reducers are also a favorite type of swiftness reducer because they offer the greatest speed reduction in the tiniest package. With a higher ratio of speed decrease and high torque output multiplier, it’s unsurprising that many power transmission systems utilize a worm equipment reducer. Some of the most common applications for worm gears are available in tuning instruments, medical examining equipment, elevators, protection gates, and conveyor belts.
SW-1 and SW-5
Torque Transmission provides two sizes of worm gear reducer, the SW-1 and the SW-5 and both can be found in a variety of ratios. The SW-1 ratios include 3.5:1 to 60:1 and the SW-5 ratios include 5:1 to 100:1. Both these options are produced with rugged compression-molded glass-fill polyester housings for a durable, long lasting, light-weight speed reducer that is also compact, non-corrosive, and nonmetallic.
Features
Our worm gear reducers offer a choice of a good or hollow output shaft and show an adjustable mounting position. Both the SW-1 and the SW-5, nevertheless, can withstand shock loading better than other decrease gearbox designs, making them perfect for demanding applications.
Rugged compression-molded glass-fill up polyester housing
Light-weight and compact
Non corrosive
Non metallic
Range of ratios
SW-1, 3.5:1 to 60:1
SW-5, 5:1 to 100:1
Grease Lubrication
Solid or Hollow output shaft
Adjustable mounting position
Worm Gear Reducers also called worm gearbox or worm speed reducers. Worm gear reducers are utilized for speed decrease and increasing the torque for electrical electric motor drives. You can decide to mount your NEMA engine to the reducer utilizing the NEMA C face flange or make use of a coupling. If you need a coupling for the result or input shaft discover our coupling section for choosing the coupling. You can expect four assemblies left hands and right hands and double result shaft and shaft input and shaft output. Interchangeable with many worm gear manufactures. Find data sheet in item overview for diamensions. If you don’t see your type, make sure you Contact Us.
8 Ratios Available from 5:1 to 60:1
7 Gear Box Sizes from 1.33 to 3.25″
Universally Interchangeable Design for OEM Replacement
Double Bearings Applied to Both Shaft Ends
Anti-Rust Primer Applied Inside and Outside Gearbox
Shaft Sleeve Protects All Shafts
S45C Carbon Metal Shafts
Flange Mount Versions for 56C and 145TC Motors
Ever-Power DDVM series triple-reduction worm gear speed reducers are available in ratios from 5000:1 to 175,000:1 and center distances from 7” to 20” (larger sizes on request). Result torque ranges from 33,000 in pounds. for the 7” CD DDVM-70 to 582,900 in pounds for the DDVM-200. Mechanical HP insight requirements are from 0.09 HP for the 175,000:1 7 in CD reducer to 6.25 HP for the 5000:1 20” CD unit. These reducers are available in four configurations: horizontal, vertical, shafted, and shaft installed.
These reducers are well suited for water/waste-water apparatus drive applications such as for example thickeners and clarifiers, which require a vertical straight down shaft. Other obtainable configurations also make Ever-Power triple decrease reducers perfect for use on mixers, elevators, solar power panels, astronomical telescopes, indexing tables, hoists, conveyors, or additional process or materials handling systems where large torques/slower speeds are needed.
These reducers are also obtainable with a helical principal reduction stage and so are termed the HDVM series
Product Features
Ratios 5000:1 to 175,000:1
HP from 0.09 to 6.25.
Output Torque to 583,000 in lbs.
Output RPM only 0.01 with a 1750 RPM input.
Ideal for ultra-slow swiftness, high torque applications
8 Ratios Available from 5:1 to 60:1
7 Gear Box Sizes from 1.33 to 3.25″
Universally Interchangeable Design for OEM Replacement
Double Bearings Applied to Both Shaft Ends
Anti-Rust Primer Applied Outside and inside Gearbox
Shaft Sleeve Protects All Shafts
S45C Carbon Steel Shafts
Flange Mount Models for 56C and 145TC Motors
Description
The HDR Series worm equipment reducers are used in low to moderate horsepower applications to reduce speeds and increase torque. Worm gear reducers can be found in direct or indirect drive, direct drive models are 56C or 145TC flange install with either right, remaining or dual result shafts or a hollow bore result. The indirect drive versions are shaft input-shaft result boxes for make use of with sprocket or pulley drive systems. They offer an effective low priced solution to speed reduction and improved torque, with higher tolerances for shock loading than helical gear reducers.
In order to select a gearbox speed reducer, you will need to determine the required torque and program factor for the application form. Click on “Specs” above for a table that will assist in identifying the service element. For service factors above 1.0, multiply the required torque by the provider factor.
Our standard 700 Series – the heart of Ever-Power rate reducer products – has been serving industry reliably for over 40 years. Its confirmed modular design has set the sector standard for functionality and may be the most imitated product in the current worm gear acceleration reducer marketplace. But why settle for a knock-off when you’re able to have the initial – from Ever-Power.
Specifications
11 basic one reduction sizes
8 basic dual reduction sizes
1/6 – 25 HP
5:1 – 100:1 ratios single reduction
100:1 – 3600:1 ratios double reduction
Non-flanged, NEMA C-face quill, and coupled input styles
Projecting and hollow result shafts
Projecting diameters from 1/2″ to 2-1/4″
Hollow result bore diameters from 5/8″ to 3-7/16″ (with over 20 bore sizes in stock)
Product Features
The 700 Series’ huge oil reservoir provides efficient heat dissipation and lubrication for longer operating existence.
Its multi-position mounting flexibility allows for installation in practically any position.
Housings are straddle-milled, top and bottom, for precise alignment of horizontal and vertical bases.
Internal baffles assure positive, leak-free venting.
The 700 Series’ rugged casing, fabricated of fine-grained, gear-quality cast iron, provides maximum strength for maximum durability, as well as greater precision during worm and gear alignment.
Ever-Power 700 Series high-strength bronze worm equipment is straddle mounted between heavy-duty tapered roller bearings to improve thrust and overhung load capacities, sizes 713-760.
Our 700 Series’ high-strength steel output shaft assures capacity for high torque and overhung loads.
Pipe plugs allow easy fill, level, and drain in virtually any mounting position.
The 700 Series’ super-finished oil-seal diameters on both input and output shafts extend seal lifestyle.
Both 2D and 3D CAD drawings can be found in our eCatalog.
TheIncreased Quality! Industrial Ranked! Inexpensive!One-piece gearcase, without exterior ribs, is constructed of close-grained cast iron and provides for rigid gear and bearing support. In addition, it offers excellent high temperature dissipation.Double lip, spring-loaded seals guard against oil leakage and stop dirt from entering.Stepped shafts with oversized ball andtapered roller bearings.Carbon metal shafts for greater strength.High tensile strength cast bronze worm wheel and hardened and floor alloy steel worm made intregal with the shaft for lengthy and trouble-free life.Essential oil sight gauge for simple maintenance (not available on sizes 25 and 34).Factory oil stuffed.Every device test run just before shipment.Universal installation with bolt-on ft.Highly modifiable design.All of this at substantially lower prices than you have been accustomed to spending money on reducers of lesser quality. Less